Solar chimney based Power Plant

The solar updraft tower (SUT) is a renewable-energy power plant for generating electricity from solar power. Sunshine heats the air beneath a very wide greenhouse-like roofed collector structure surrounding the central base of a very tall chimney tower. The resulting convection causes a hot air updraft in the tower by the chimney effect. This airflow drives wind turbines placed in the chimney updraft or around the chimney base to produce electricity. Plans for scaled-up versions of demonstration models will allow significant power generation, and may allow development of other applications, such as water extraction or distillation, and agriculture or horticulture. As a solar chimney power plant (SCPP) proposal for electrical power generation, commercial investment is discouraged by the high initial cost of building a very large novel structure, and by the risk of investment in a feasible but unproven application of even proven component technology for long-term returns on investment—especially when compared to the proven and demonstrated greater short-term returns on lesser investment in coal-fired or nuclear power plants Power output depends primarily on two factors: collector area and chimney height. A larger area collects and warms a greater volume of air to flow up the chimney; collector areas as large as 7 kilometres (4.3 mi) in diameter have been discussed. A larger chimney height increases the pressure difference via the stack effect; chimneys as tall as 1,000 metres (3,281 ft) have been discussed. Heat can be stored inside the collector area. The ground beneath the solar collector, water in bags or tubes, or a saltwater thermal sink in the collector could add thermal capacity and inertia to the collector. Humidity of the updraft and condensation in the chimney could increase the energy flux of the system. Turbines with a horizontal axis can be installed in a ring around the base of the tower, as once planned for an Australian project and seen in the diagram above; or—as in the prototype in Spain—a single vertical axis turbine can be installed inside the chimney. Carbon dioxide is emitted only negligibly as part of operations. Manufacturing and construction require substantial power, particularly to produce cement. Net energy payback is estimated to be 2–3 years. Since solar collectors occupy significant amounts of land, deserts and other low-value sites are most likely. A small-scale solar updraft tower may be an attractive option for remote regions in developing countries. The relatively low-tech approach could allow local resources and labour to be used for construction and maintenance. Locating a tower at high latitudes could produce up to 85 per cent of the output of a similar plant located closer to the equator, if the collection area is sloped significantly toward the equator. The sloped collector field, which also functions as a chimney, is built on suitable mountainsides, with a short vertical chimney on the mountaintop to accommodate the vertical axis air turbine. The results showed that solar chimney power plants at high latitudes may have satisfactory thermal performance. Solar updraft towers can be combined with other technologies to increase output. Solar thermal collectors or photovoltaics can be arranged inside the collector greenhouse. This could further be combined with agriculture The solar updraft tower has a power conversion rate considerably lower than many other designs in the (high temperature) solar thermal group of collectors. The low conversion rate is balanced to some extent by the lower cost per square metre of solar collection. Model calculations estimate that a 100 MW plant would require a 1,000 m tower and a greenhouse of 20 square kilometres (7.7 sq mi). A 200 MW tower with the same tower would require a collector 7 kilometres in diameter (total area of about 38 km²). One 200MW power station will provide enough electricity for around 200,000 typical households and will abate over 900,000 tons of greenhouse producing gases from entering the environment annually. The collector area is expected to extract about 0.5 percent, or 5 W/m² of 1 kW/m², of the solar energy that falls upon it. Concentrating thermal (CSP) or photovoltaic (CPV) solar power plants range between 20% to 31.25% efficiency (dish Stirling). Overall CSP/CPV efficiency is reduced because collectors do not cover the entire footprint. Without further tests, the accuracy of these calculations is uncertain. Most of the projections of efficiency, costs and yields are calculated theoretically, rather than empirically derived from demonstrations, and are seen in comparison with other collector or solar heat transducing technologies. The performance of an updraft tower may be degraded by factors such as atmospheric winds, by drag induced by the bracings used for supporting the chimney, and by reflection off the top of the greenhouse canopy. At present, a number of energy sources are utilized on a large scale such as: coil, oil, gas and nuclear. Continuation of the use of fossil fuels is set to face multiple challenges namely: depletion of fossil fuels reserves, global warming and other environmental concerns and continuing fuel price rise. For these reasons, the existing sources of conventional energy may not be adequate to meet the ever increasing energy demands. Consequently sincere and untiring efforts shall have to be made by the scientists and engineers in exploring the possibilities of harnessing energy from several non-conventional energy sources (solar, biomass, tidal, hydrogen, wind and geothermal energy) which they are seen as possible solution to the growing energy challenges. According to energy experts, unconventional energy sources can be used for electric power generation which receives a great attention. Power generating technology based on green resources would help many countries improve their balance of payments. Being the most abundant and well distributed form of renewable energy, solar energy constitutes a big asset for arid and semi-arid regions. A range of solar technologies are used throughout the world to harvest the sun‘s energy. In the last years, an exciting innovation has been introduced by researchers called ―solar chimney‖. It is a solar thermal driven electrical power generation plant which converts the solar thermal energy into electrical power in a complex heat transfer process. The implementation of this project is of great significance for the development of new energy resources and the commercialization of power generating systems of this type and will help developing countries to promote the rapid development of the solar hot air-flows power generation. The basic physical principles of centralized electricity generation with solar chimney power plants (SCPP‘s) were described by Haaf et al. in 1982. After the pilot plant in Manzanares had gone into operation in June 1982, the first experimental results confirmed the main assumptions of the original physical model. Later, on the basis of experimental data from July 1983 to January 1984, a semi-empirical, parametrical model was proposed for predicting the monthly mean electrical power output of the pilot plant as a function of solar irradiation. The model predictions agreed reasonably with the experimental data for the exceptionally dry months July- October 1983, but the model failed to simulate the wet months following heavy rainfall in winter and spring 1984. It was realized, that natural precipitation entering the collector has a fundamental influence on the collector performance via evaporation, plant growth and infrared absorption in the collector air. A refined parametrical model was therefore proposed, which includes at least the long term, seasonally varying effect on rainwater on the plants performance and allows the simulation of large plants in climates similar to the climate in Manzanares. Solar chimney power plants are an interesting alternative to centralized electricity generation power plants. It is an ideally adapted technology for countries that lack a sophisticated technical infrastructure, where simplicity and uncritical operation of the installation is of crucial importance. A detailed literature survey of this system was performed. The review discusses the principles and characteristics of such a system, its requirements, its construction and its operation. It gives also a brief overview of the present state of research at the solar chimney power plant and future prospects for large-scale plants.

Geothermal Energy: A brief Overview

Geothermal energy is the heat from the Earth. It's clean and sustainable. Resources of geothermal energy range from the shallow ground to hot water and hot rock found a few miles beneath the Earth's surface, and down even deeper to the extremely high temperatures of molten rock called magma. Almost everywhere, the shallow ground or upper 10 feet of the Earth's surface maintains a nearly constant temperature between 50° and 60°F (10° and 16°C). Geothermal heat pumps can tap into this resource to heat and cool buildings. A geothermal heat pump system consists of a heat pump, an air delivery system (ductwork), and a heat exchanger-a system of pipes buried in the shallow ground near the building. In the winter, the heat pump removes heat from the heat exchanger and pumps it into the indoor air delivery system. In the summer, the process is reversed, and the heat pump moves heat from the indoor air into the heat exchanger. The heat removed from the indoor air during the summer can also be used to provide a free source of hot water. In the United States, most geothermal reservoirs of hot water are located in the western states, Alaska, and Hawaii. Wells can be drilled into underground reservoirs for the generation of electricity. Some geothermal power plants use the steam from a reservoir to power a turbine/generator, while others use the hot water to boil a working fluid that vaporizes and then turns a turbine. Hot water near the surface of Earth can be used directly for heat. Direct-use applications include heating buildings, growing plants in greenhouses, drying crops, heating water at fish farms, and several industrial processes such as pasteurizing milk. Hot dry rock resources occur at depths of 3 to 5 miles everywhere beneath the Earth's surface and at lesser depths in certain areas. Access to these resources involves injecting cold water down one well, circulating it through hot fractured rock, and drawing off the heated water from another well. Currently, there are no commercial applications of this technology. Existing technology also does not yet allow recovery of heat directly from magma, the very deep and most powerful resource of geothermal energy. Most power plants need steam to generate electricity. The steam rotates a turbine that activates a generator, which produces electricity. Many power plants still use fossil fuels to boil water for steam. Geothermal power plants, however, use steam produced from reservoirs of hot water found a couple of miles or more below the Earth's surface. There are three types of geothermal power plants:dry steam, flash steam, and binary cycle. Dry steam power plants draw from underground resources of steam. The steam is piped directly from underground wells to the power plant, where it is directed into a turbine/generator unit. There are only two known underground resources of steam in the United States: The Geysers in northern California and Yellowstone National Park in Wyoming, where there's a well-known geyser called Old Faithful. Since Yellowstone is protected from development, the only dry steam plants in the country are at The Geysers. Flash steam power plants are the most common. They use geothermal reservoirs of water with temperatures greater than 360°F (182°C). This very hot water flows up through wells in the ground under its own pressure. As it flows upward, the pressure decreases and some of the hot water boils into steam. The steam is then separated from the water and used to power a turbine/generator. Any leftover water and condensed steam are injected back into the reservoir, making this a sustainable resource. Binary cycle power plants operate on water at lower temperatures of about 225°-360°F (107°-182°C). These plants use the heat from the hot water to boil a working fluid, usually an organic compound with a low boiling point. The working fluid is vaporized in a heat exchanger and used to turn a turbine. The water is then injected back into the ground to be reheated. The water and the working fluid are kept separated during the whole process, so there are little or no air emissions. Small-scale geothermal power plants (under 5 megawatts) have the potential for widespread application in rural areas, possibly even as distributed energy resources. Distributed energy resources refer to a variety of small, modular power-generating technologies that can be combined to improve the operation of the electricity delivery system. When a person takes a hot bath, the heat from the water will usually warm up the entire bathroom. Geothermal reservoirs of hot water, which are found a couple of miles or more beneath the Earth's surface, can also be used to provide heat directly. This is called the direct use of geothermal energy. Geothermal direct use dates back thousands of years, when people began using hot springs for bathing, cooking food, and loosening feathers and skin from game. Today, hot springs are still used as spas. But there are now more sophisticated ways of using this geothermal resource. In modern direct-use systems, a well is drilled into a geothermal reservoir to provide a steady stream of hot water. The water is brought up through the well, and a mechanical system - piping, a heat exchanger, and controls - delivers the heat directly for its intended use. A disposal system then either injects the cooled water underground or disposes of it on the surface. Geothermal hot water can be used for many applications that require heat. Its current uses include heating buildings (either individually or whole towns), raising plants in greenhouses, drying crops, heating water at fish farms, and several industrial processes, such as pasteurizing milk. With some applications, researchers are exploring ways to effectively use the geothermal fluid for generating electricity as well. The shallow ground, the upper 10 feet of the Earth, maintains a nearly constant temperature between 50° and 60°F (10°-16°C). Like a cave, this ground temperature is warmer than the air above it in the winter and cooler than the air in the summer. Geothermal heat pumps take advantage of this resource to heat and cool buildings. Geothermal heat pump systems consist of basically three parts: the ground heat exchanger, the heat pump unit, and the air delivery system (ductwork). The heat exchanger is basically a system of pipes called a loop, which is buried in the shallow ground near the building. A fluid (usually water or a mixture of water and antifreeze) circulates through the pipes to absorb or relinquish heat within the ground. In the winter, the heat pump removes heat from the heat exchanger and pumps it into the indoor air delivery system. In the summer, the process is reversed, and the heat pump moves heat from the indoor air into the heat exchanger. The heat removed from the indoor air during the summer can also be used to heat water, providing a free source of hot water. Geothermal heat pumps use much less energy than conventional heating systems, since they draw heat from the ground. They are also more efficient when cooling your home. Not only does this save energy and money, it reduces air pollution.

Tidal Energy: A Introduction & Technical Aspects

Tidal energy is one of the oldest forms of energy used by humans. Indeed, tide mills, in use on the Spanish, French and British coasts, date back to 787 A.D.. Tide mills consisted of a storage pond, filled by the incoming (flood) tide through a sluice and emptied during the outgoing (ebb) tide through a water wheel. The tides turned waterwheels, producing mechanical power to mill grain. We even have one remaining in New York- which worked well into the 20th century. Tidal power is non-polluting, reliable and predictable. Tidal barrages, undersea tidal turbines – like wind turbines but driven by the sea – and a variety of machines harnessing undersea currents are under development. Unlike wind and waves, tidal currents are entirely predictable. Tidal energy can be exploited in two ways: 1. By building semi-permeable barrages across estuaries with a high tidal range. 2. By harnessing offshore tidal streams. Barrages allow tidal waters to fill an estuary via sluices and to empty through turbines. Tidal streams can be harnessed using offshore underwater devices similar to wind turbines. Most modern tidal concepts employ a dam approach with hydraulic turbines. A drawback of tidal power is its low capacity factor, and it misses peak demand times because of 12.5 hr cycle of the tides. The total world potential for ocean tidal power has been estimated at 64,000 MWe. The 25-30 ft tidal variations of Passamaquoddy Bay (Bay of Fundy) have the potential of between 800 to 14,000 MWe Tidal range may vary over a wide range (4.5-12.4 m) from site to site. A tidal range of at least 7 m is required for economical operation and for sufficient head of water for the turbines. Hammerfest Traditional tidal electricity generation involves the construction of a barrage across an estuary to block the incoming and outgoing tide. The dam includes a sluice that is opened to allow the tide to flow into the basin; the sluice is then closed, and as the sea level drops, the head of water (elevated water in the basin) using traditional hydropower technology, drives turbines to generate electricity. Barrages can be designed to generate electricity on the ebb side, or flood side, or both. Tidal range may vary over a wide range (4.5-12.4 m) from site to site. A tidal range of at least 7 m is required for economical operation and for sufficient head of water for the turbines. A 240 MWe facility has operated in France since 1966, 20 MWe in Canada since 1984, and a number of stations in China since 1977, totaling 5 mWw. Tidal energy schemes are characterised by low capacity factors, usually in the range of 20-35%. The waters off the Pacific Northwest are ideal for tapping into an ocean of power using newly developed undersea turbines. The tides along the Northwest coast fluctuate dramatically, as much as 12 feet a day. The coasts of Alaska, British Columbia and Washington, in particular, have exceptional energy-producing potential. On the Atlantic seaboard, Maine is also an excellent candidate. The undersea environment is hostile so the machinery will have to be robust. Currently, although the technology required to harness tidal energy is well established, tidal power is expensive, and there is only one major tidal generating station in operation. This is a 240 megawatt (1 megawatt = 1 MW = 1 million watts) at the mouth of the La Rance river estuary on the northern coast of France (a large coal or nuclear power plant generates about 1,000 MW of electricity). The La Rance generating station has been in operation since 1966 and has been a very reliable source of electricity for France. La Rance was supposed to be one of many tidal power plants in France, until their nuclear program was greatly expanded in the late 1960’s. Elsewhere there is a 20 MW experimental facility at Annapolis Royal in Nova Scotia, and a 0.4 MW tidal power plant near Murmansk in Russia. UK has several proposals underway. Studies have been undertaken to examine the potential of several other tidal power sites worldwide. It has been estimated that a barrage across the Severn River in western England could supply as much as 10% of the country’s electricity needs (12 GW). Similarly, several sites in the Bay of Fundy, Cook Inlet in Alaska, and the White Sea in Russia have been found to have the potential to generate large amounts of electricity. WHAT IS THE IMPACT ON THE ENVIRONMENT? Tidal energy is a renewable source of electricity which does not result in the emission of gases responsible for global warming or acid rain associated with fossil fuel generated electricity. Use of tidal energy could also decrease the need for nuclear power, with its associated radiation risks. Changing tidal flows by damming a bay or estuary could, however, result in negative impacts on aquatic and shoreline ecosystems, as well as navigation and recreation. The few studies that have been undertaken to date to identify the environmental impacts of a tidal power scheme have determined that each specific site is different and the impacts depend greatly upon local geography. Local tides changed only slightly due to the La Rance barrage, and the environmental impact has been negligible, but this may not be the case for all other sites. It has been estimated that in the Bay of Fundy, tidal power plants could decrease local tides by 15 cm. This does not seem like much when one considers that natural variations such as winds can change the level of the tides by several metres. WHAT ARE THE COSTS OF TIDAL ENERGY? Tidal power is a form of low-head hydroelectricity and uses familiar low-head hydroelectric generating equipment, such as has been in use for more than 120 years. The technology required for tidal power is well developed, and the main barrier to increased use of the tides is that of construction costs. There is a high capital cost for a tidal energy project, with possibly a 10-year construction period. Therefore, the electricity cost is very sensitive to the discount rate. The major factors in determining the cost effectiveness of a tidal power site are the size (length and height) of the barrage required, and the difference in height between high and low tide. These factors can be expressed in what is called a site’s “Gibrat” ratio. The Gibrat ratio is the ratio of the length of the barrage in metres to the annual energy production in kilowatt hours (1 kilowatt hour = 1 KWH = 1000 watts used for 1 hour). The smaller the Gibrat site ratio, the more desireable the site. Examples of Gibrat ratios are La Rance at 0.36, Severn at 0.87 and Passamaquoddy in the Bay of Fundy at 0.92. Offshore tidal power generators use familiar and reliable low-head hydroelectric generating equipment, conventional marine construction techniques, and standard power transmission methods. The placement of the impoundment offshore, rather than using the conventional “barrage” approach, eliminates environmental and economic problems that have prevented the deployment of commercial-scale tidal power plants. Three projects (Swansea Bay 30 MW, Fifoots Point 30 MW, and North Wales 432 MW) are in development in Wales where tidal ranges are high, renewable source power is a strong public policy priority , and the electricity marketplace gives it a competitive edge. Q. What are some of the devices for tidal energy conversion? The technology required to convert tidal energy into electricity is very similar to the technology used in traditional hydroelectric power plants. The first requirement is a dam or “barrage” across a tidal bay or estuary. Building dams is an expensive process. Therefore, the best tidal sites are those where a bay has a narrow opening, thus reducing the length of dam which is required. At certain points along the dam, gates and turbines are installed. When there is an adequate difference in the elevation of the water on the different sides of the barrage, the gates are opened. This “hydrostatic head” that is created, causes water to flow through the turbines, turning an electric generator to produce electricity. Electricity can be generated by water flowing both into and out of a bay. As there are two high and two low tides each day, electrical generation from tidal power plants is characterized by periods of maximum generation every twelve hours, with no electricity generation at the six hour mark in between. Alternatively, the turbines can be used as pumps to pump extra water into the basin behind the barrage during periods of low electricity demand. This water can then be released when demand on the system its greatest, thus allowing the tidal plant to function with some of the characteristics of a “pumped storage” hydroelectric facility. WHAT ARE SOME OF THE DEVICES FOR TIDAL ENERGY CONVERSION? The technology required to convert tidal energy into electricity is very similar to the technology used in traditional hydroelectric power plants. The first requirement is a dam or “barrage” across a tidal bay or estuary. Building dams is an expensive process. Therefore, the best tidal sites are those where a bay has a narrow opening, thus reducing the length of dam which is required. At certain points along the dam, gates and turbines are installed. When there is an adequate difference in the elevation of the water on the different sides of the barrage, the gates are opened. This “hydrostatic head” that is created, causes water to flow through the turbines, turning an electric generator to produce electricity. Electricity can be generated by water flowing both into and out of a bay. As there are two high and two low tides each day, electrical generation from tidal power plants is characterized by periods of maximum generation every twelve hours, with no electricity generation at the six hour mark in between. Alternatively, the turbines can be used as pumps to pump extra water into the basin behind the barrage during periods of low electricity demand. This water can then be released when demand on the system its greatest, thus allowing the tidal plant to function with some of the characteristics of a “pumped storage” hydroelectric facility. WHY TIDAL ENERGY? The demand for electricity on an electrical grid varies with the time of day. The supply of electricity from a tidal power plant will never match the demand on a system. But, due to the lunar cycle and gravity, tidal currents, although variable, are reliable and predictable and their power can make a valuable contribution to an electrical system which has a variety of sources. Tidal electricity can be used to displace electricity which would otherwise be generated by fossil fuel (coal, oil, natural gas) fired power plants, thus reducing emissions of greenhouse and acid gasses. Tidal power, also called tidal energy, is a form of hydropower that converts the energy of tides into useful forms of power, mainly electricity. Although not yet widely used, tidal power has potential for future electricity generation. Tides are more predictable than wind energy and solar power. Among sources of renewable energy, tidal power has traditionally suffered from relatively high cost and limited availability of sites with sufficiently high tidal ranges or flow velocities, thus constricting its total availability. However, many recent technological developments and improvements, both in design (e.g. dynamic tidal power, tidal lagoons) and turbine technology (e.g. new axial turbines, cross flow turbines), indicate that the total availability of tidal power may be much higher than previously assumed, and that economic and environmental costs may be brought down to competitive levels. Historically, tide mills have been used both in Europe and on the Atlantic coast of North America. The incoming water was contained in large storage ponds, and as the tide went out, it turned waterwheels that used the mechanical power it produced to mill grain. The earliest occurrences date from the Middle Ages, or even from Roman times. It was only in the 19th century that the process of using falling water and spinning turbines to create electricity was introduced in the U.S. and Europe. The world's first large-scale tidal power plant is the Rance Tidal Power Station in France, which became operational in 1966. Tidal power is taken from the Earth's oceanic tides; tidal forces are periodic variations in gravitational attraction exerted by celestial bodies. These forces create corresponding motions or currents in the world's oceans. Due to the strong attraction to the oceans, a bulge in the water level is created, causing a temporary increase in sea level. When the sea level is raised, water from the middle of the ocean is forced to move toward the shorelines, creating a tide. This occurrence takes place in an unfailing manner, due to the consistent pattern of the moon’s orbit around the earth.[5] The magnitude and character of this motion reflects the changing positions of the Moon and Sun relative to the Earth, the effects of Earth's rotation, and local geography of the sea floor and coastlines. Tidal power is the only technology that draws on energy inherent in the orbital characteristics of the Earth–Moon system, and to a lesser extent in the Earth–Sun system. Other natural energies exploited by human technology originate directly or indirectly with the Sun, including fossil fuel, conventional hydroelectric, wind, biofuel, wave and solar energy. Nuclear energy makes use of Earth's mineral deposits of fissionable elements, while geothermal power taps the Earth's internal heat, which comes from a combination of residual heat from planetary accretion (about 20%) and heat produced through radioactive decay (80%). A tidal generator converts the energy of tidal flows into electricity. Greater tidal variation and higher tidal current velocities can dramatically increase the potential of a site for tidal electricity generation. Because the Earth's tides are ultimately due to gravitational interaction with the Moon and Sun and the Earth's rotation, tidal power is practically inexhaustible and classified as a renewable energy resource. Movement of tides causes a loss of mechanical energy in the Earth–Moon system: this is a result of pumping of water through natural restrictions around coastlines and consequent viscous dissipation at the seabed and in turbulence. This loss of energy has caused the rotation of the Earth to slow in the 4.5 billion years since its formation. During the last 620 million years the period of rotation of the earth (length of a day) has increased from 21.9 hours to 24 hours; in this period the Earth has lost 17% of its rotational energy. While tidal power will take additional energy from the system, the effect is negligible and would only be noticed over millions of years.[8]